And that is it, now just run your WoL Tool and the System should wake up and boot to Windows.Configure the physical address of the computer you want to wake up (here you need the address you noted before).On another System in your Network, download and open your Wake on LAN Tool.You’ll have to set your network adapter to respond to the magic packet. If Wake-on-LAN is enabled in your BIOS, your next step is to enable it as a feature in Windows 10. Disabled - Does not allows the system to power on by special LAN signals when it receives a wake-up signal from the LAN or wireless LAN. If it isn’t, the WOL magic packet (used to switch your PC back on) won’t turn on your PC. Shut down your computer again, or send it into standby. Make sure the setting for Wake-on-LAN is set to On or Enabled.Note the physical address of your LAN-Adapter.įigure 1: Physical Address of the Network Adapter.Open start type in CMD, right-click command prompt and choose Run as Administrator. Once in Windows, open the command prompt with administrator rights. Start the System that you want to wake up.To configure your Wake on LAN Tool follow these steps (steps may vary on other tools): You can find plenty of them in a Websearch like Bing or Google. Please choose the Wake on LAN tool that suits your needs and download it. Or redirecting to another location such as this:ĮnableWOL-2Settings.exe /l="%windir%\temp\enableWOL.txt"Īnyway, hopefully this can help out someone else.NOTE: Dell does not endorse this Software and using it is at your own risk. I was able to work around this by either disabling logging by adding a "/nolog" argument to the CCTK SCE Program in SCCM: HOWEVER, in my environment, my attempt to deploy a CCTK SCE via a SCCM 2007 software distribution failed in my lab with an exit code of 10 for all my machines for whatever reason. This CCTK command line run on your machines would perform the required BIOS level configurations to get WOL working on these machine models.ĬCTK also has the ability to create self-contained executable files (SCE) that you can deploy to your machines without having to install CCTK on each device. Once you have CCTK up and running, the CCTK command line to perform steps 2 and 3 would look something like this:Ĭctk.exe -deepsleepctrl=disable -wakeonlan=enable Optiplex 780 models do not support the "s5only" value as far as I can tell, but the other two work. The CCTK documentation mentions that the deepsleepctrl switch supports three values: "s5only", "s4ands5", "disable". The deepsleepctrl switch also allows for changes to the "Low Power Mode" setting on the 780s, but the documentation does not explicitly state this (even though the terminology slightly changed). WOL works with Hibernate enabled, too, at least on a Dell OptiPlex 7040 and on my clone with an Asus Z170-A motherboard. At the command prompt, type powercfg.exe /hibernate off, and then press Enter. The settings for 2 and 3 can be done manually via the BIOS configuration, or using the "Dell Client Configuration Toolkit" (CCTK) tool.ĭell released a new version (2.2.1) of the CCTK tool on Octothat supports making changes to the applicable power control settings using the -deepsleepctrl switch. In the search results list, right-click Command Prompt, and then click Run as Administrator. To configure your Wake on LAN Tool follow these steps (steps may vary on other tools): Start the System that you want to wake up. Until all three of these were done, the machines would only wake up from Standby, not from full shutdown. Disable "Low Power Mode" (for the 780) or "Deep Sleep Mode" (for the 7) in the BIOS. Enable WOL (also called "remote wake up") for the wired NIC in the BIOS.ģ. Enable WOL on the wired network card in the OS.Ģ. I've found there are there are three settings that need to be in place for this to function:ġ. It might work on older/newer models, YMMV. ![]() This has been tested and works on Optiplex models: 780, 7. I did some digging and poking and eventually got it to work and I thought I would share my findings. My co-worker asked me to try to get Wake-On-LAN from power-off state working on the Optiplex models in our lab.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |